A. Applications in Construction Chemistry
 

 

 

B. (mineral or emulsion-bound) and Bituminous Products
ARBOCEL Selection Critera

The most suitable ARBOCEL grade depends on:

- The required profile of the finished product(e.g surface, color, etc.)

- Type of mixer (Dry system or ready-to-use system)

- Application of the product

- Metering requirements

Our experts will be happy to help you finding the optimum ARBOCEL grade for your application.

 

 

 

General Correlation:
fiber length / effectiveness / mixing behavior:

ARBOCEL type Fiber length Effectiveness
Mixing behavior
In dry mixtures
In aqueous systems
BE 600/30 PU
Short
Ø 40 µm
Low
Very good
Very good
PWC 500
Short
Ø 500 µm
Good
Good
Very good
B 400
Short
Ø 900 µm
Very good

Possible*

Good

* If you have any difficulties blending ARBOCEL we will be happy to help you.

 

 

 

C. Mineral / Dry Systems
Applications / Quantities Used

Power adhesives (cement tile adhesives)

0.4 - 0.5 % ARBOCEL FD 40 or ARBOCEL BWW 40 by weight
0.3 - 0.4 % ARBOCEL ZZ 8/2 CA 1 by weight

Advantages with ARBOCEL:
- Good slump resistance of the adhesive (reduced tile slip)
- Improved workability (thick without the need to exert great force)
- Reduces undesirable sticking to tools
- In many case longer open time and better adhesion strength

سیستم های معدنی / سیستم های خشک

کاربردها / مقادیر استفاده شده
چسبهای پودری (چسب های کاشی سیمانی)

0.4 تا 0.5درصدوزنی ARBOCEL FD 40 یا ARBOCEL BWW 40 یا
0.3 تا 0.4 درصدوزنی AEBOCEL ZZ 8/2 CA 1


مزیت های ARBOCEL :
- مقاومت بالا در برابر جمع شدن چسب (کاهش لغزندگی کاشی یا سرامیک)
- بهبود کارایی (ضخیم بدون نیاز به اعمال نیروی بیشتر)
- چسبندگی نامطلوب به ابزار را کاهش می دهد.
- در بیشتر موارد دارای زمان باز (open time ) طولانی تر و مقاومت به چسبندگی بهتر است.

 

 

 

Stuccos / Plasters

a) Mineral stucco finish coats
(cement / lime-cement*): gypsum, gypsum / lime*

0.4 - 0.1 % ARBOCEL PWC 500 or ARBOCEL FD 540 CA by weight

Advantages with ARBOCEL:
- Good slump resistance
- Improved workability
- Inhibits cracking after application and during setting
- Improves texturing (sharp contours)

*binder

گچ ها / Stuccos

پوشش های صیقلی Stuccoمعدنی

(سیمان / سیمان- آهک) : گچ / گچ آهک

ARBOCEL PWC 500 ، ARBOCEL FLP 500 یا ARBOCEL FL 540 CA  با درصد وزنی 0.4 تا 0.1 %


مزیت های ARBOCEL :
- مقاومت بالا در برابر جمع شدگی
- بهبود کاراییی
- ممانعت از ترک خوردگی بعد از کاربرد و در طول کار
- بهبود بافت (sharp contours )

 

b) Mineral insulating plasters

0.3 - 0.5 % ARBOCEL PWC 500 or ARBOCEL ZZC 500 by weight

Advantages with ARBOCEL:
- Very good slump resistance
(even when applied in thick coat)
- Improved workability
- Separation inhibitor for dry ready-to-use mixtures

گچ های عایق بندی معدنی

ARBOCEL PW 500  با ARBOCEL ZZC 500 با درصد وزنی 0.3 تا 0.5 %


مزیت های ARBOCEL :
- مقاومت بالا در برابر جمع شدگی (حتی زمانی که با ضخامت بالایی مورد استفاده قرار می گیرد)
- بهبود کارایی
- بازدارنده جدا شدگی برای مخلوط های آماده استفاده

 

c) Mineral Stucco / Plaster base coats

0.2 - 0.5 % ARBOCEL PWC 500 or ARBOCEL ZZC 500 by weight

Advantages with ARBOCEL:
- Esay to work when smoothing
(even when applied in thick coat)
- Separation inhibitor for dry ready-to-use mixtures
- Improved slump resistance

پوشش های پایه گچی / Stuccoمعدنی

ARBOCEL PW 500  با ARBOCEL ZZC 500 با درصد وزنی 0.2 تا 0.5 %

مزیت های ARBOCEL :
- آسانی کار کردن در هنگام صاف کردن
- بازدارنده جدا شدگی برای مخلوط های آماده استفاده
- مقاومت بالا در برابر جمع شدگی

 

d) Mineral Stucco / Plaster light base coats

Binder: plaster, plaster / lime:
0.2 - 0.3 % ARBOCEL PWC 500 or ARBOCEL ZZC 500 by weight

Binder: cement, cement / lime:
0.2 - 0.3 % ARBOCEL PWC 500 or ARBOCEL ZZC 500 by weight

Advantages with ARBOCEL:
- Esay to work when smoothing
- Improves yield of the plaster
- Separation inhibitor for dry ready-to-use mixtures

- Longer life of worm conveyors
- Improved slump resistance

پوشش های پایه سبک گچی / Stuccoمعدنی

متصل کننده: گچ، گچ / آهک: ARBOCEL PW 500  با ARBOCEL ZZC 500 با درصد وزنی 0.2 تا 0.3 %

متصل کننده: سیمان، سیمان / آهک: ARBOCEL PW 500  با ARBOCEL ZZC 500 با درصد وزنی 0.2 تا 0.3 %


مزیت های ARBOCEL :
- آسانی کار کردن با آن در هنگام صاف کردن
- بهبود تسلیم شدن گچ
- بازداری جدا شدگی برای مخلوط های آماده استفاده
- پایداری طولانی تر دربرابرحمل کننده های کرمی(worm conveyor)
- مقاومت بالا در برابر جمع شدگی

 

 

 

Adhesive and reinforcing compounds in exterior insulation finishing system (EIFS)

Approx. 0.3 % ARBOCEL PWC 500 or
ARBOCEL ZZC 500 by weight

Advantages with ARBOCEL:
- Good slump resistance
- Improves working properties
- Reduction of formulation costs

چسب و ترکیبات تقویت کننده در سیستم های عایق کمپوزیت حرارتی (EFIS)

تقریباً 0.3 وزنی ARBOCEL PWC 500 یا ARBOCEL ZZC 500

مزیت های ARBOCEL :
- آسانی کار کردن با آن در هنگام صاف کردن - مقاومت بالا در برابر جمع شدگی
- بهبود ویژگی های کاری
- کاهش هزینه های فرمولاسیون

 

 

 

Joint fillers for plasterboards

0.5 - 1.0 % ARBOCEL FD 40 or
ARBOCEL FD 00 by weight

Advantages with ARBOCEL:
- Reduces cracking and shrinkage
- Improves workability
- Improves standability

فیلرهای اتصال برای صفحات گچی (plasterboards)

ARBOCEL FD 40 یا ARBOCEL FD 00 با درصدوزنی 0.5 تا1 %

مزیت های ARBOCEL :
- کاهش ترک خوردگی و جمع شدگی
- بهبود کارایی
- بهبود قابلیت مخلوط شدن با ماسه و شن

 

 

 

Fillers compounds and joint fillers

0.5 - 1.0 % ARBOCEL FD 00 or
ARBOCEL FD 40 by weight

Advantages with ARBOCEL:
- Reduces cracking and shrinkage
- Improves workability
- Improves standability

ترکیبات فیبر و فیلرهای اتصال

ARBOCEL FD 00 یا ARBOCEL FD 40 با درصدوزنی 0.5 تا1 %

مزیت های ARBOCEL :
- کاهش ترک خوردگی و جمع شدگی
- بهبود کارایی
- بهبود قابلیت مخلوط شدن با ماسه و شن

 

 

 

Pastes for heavy wallpapers

3.0 % ARBOCEL BWW 40 by weight
5.0 % ARBOCEL B 600 by weight

Advantages with ARBOCEL:
- Improves workability
- Less tendency to splatter when being applied
- Formulation costs can be reduced

چسب های مخصوص کاغذ دیواری های سنگین

ARBOCEL BWW با 3% وزنی
با 5% وزنی ARBOCEL B600

مزیت های ARBOCEL :
- بهبود کارایی
- قابلیت ترشح کمتر در هنگام کار کردن
- هزینه های فرمولاسیون پایین تر

 

 

 

Construction adhesives

0.2 - 0.5 % ARBOCEL ZZC 500 by weight

Advantages with ARBOCEL:
- Improves workability
- Reduces tool sticking
- Optimizes formulation costs

- Improves slump resistance

چسب ساختمانی

 0.5 - 0.2 درصد وزن آربوسل ZZC 500

مزیت های ARBOCEL :
- بهبود کارایی - قابلیت ساخت و پرداخت بهتر
- کاهش چسبندگی به ابزار آلات
- بهینه سازی هزینه های فرمول بندی
- مقاومت بهتر

 

 

 

Extruded spacers for steel mats in concrete constuction

0.1 - 1.0 % ARBOCEL ZZ 8/1 G by weight

Advantages with ARBOCEL:
- Extruction aid
- Improves slump resistance
- Formulation costs can be optimized

اتصال دهنده بیرونی برای پوششهای فولادی در
سازه های بتونی

1.0 - 0.1 درصد وزن آربوسل ZZ 8/1

مزیت های ARBOCEL :
- ماده کمکی برای Extrusions
- مقاومت کمتر در مرحله ماسه تر
- در هزینه های فرمول بندی می توان صرفه جویی کرد

 

 

 

Extruded cement profiles (e.g. window ledges)

3.0 - 5.0 % ARBOCEL ZZ 8/1 G by weight

Advantages with ARBOCEL:
- Extruction aid
- Improves slump resistance

پروفیل های سیمانی Extrusions (به طورمثال قرنیز پنجره)

5 - 3 درصد وزن آربوسل ZZ 8/1

مزیت های ARBOCEL :
- ماده کمکی برای Extrusions
- مقاومت کمتر در مرحله ماسه تر

 

 

 

Skin Coats

1.0 - 3.0 % ARBOCEL FD 00 by weight

Advantages with ARBOCEL:
- Suppresses cracking
- Improves working properties

ورق های اندود نازک

3 - 1  درصد وزن آربوسل FD 00

مزیت های ARBOCEL :
- ماده کمکی برای Extrusions - پوشاندن درز و ترک
- ویژگیهای ساخت و پرداخت بهتر

 

 

 

D. Emulsion - Bound Systems / Paste Systems

ARBOCEL Grades Used

ARBOCEL BE 600/30 PU, ARBOCEL B 00,
ARBOCEL BWW 40 and ARBOCEL B 400

 

 

 

Mixing Notes:
Blending ARBOCEL fibers is usually straight forward. The addition of wetting agents is normally not required. In order to reach the final viscosity more quickly, it is advisable to add ARBOCEL in the aqueous phase. ARBOCEL can also be added after production of the batch for controlling viscosity. IF dissolvers are used, it is recommended that ARBOCEL be added at the end of the mixing process. Even small amounts of ARBOCEL will significantly increase the viscosity of an emulsion- bound system. The longer the fibers of the ARBOCEL type used, the greater is the viscosity increase.

Guidance Note
The consistency of the ARBOCEL formulation must be set for an optimum tradeoff between workability and slump resistance. Keep in mind that with systems containing ARBOCEL it is not the apparent consistency at rest that should be set but rather the working consistency.
systems in which ARBOCEL is completely at rest are more viscous.

Applications / Quantities Used

Synthetic resin coatings

Exterior use: 0.2 - 0.4 % ARBOCEL B 400 or
ARBOCEL BC 1000 by weight

Interior use: 0.5 - 2.0 % ARBOCEL B 400 or
ARBOCEL BC 1000 by weight

Advantages with ARBOCEL:
- Good slump resistance
- Improved workability
- Prevents cracking
- Very good texturing (sharp contours)

 

Joint fillers for Plasterboards

0.5 - 1.0 % ARBOCEL B 00 by weight

Advantages with ARBOCEL:
- Reduces cracking and shrinkage
- Improves workability
- Improves standability

 

Emulsion tile adhesives

0.4 - 0.5 % ARBOCEL BWW 40 or
ARBOCEL BC 200 by weight

Advantages with ARBOCEL:
- Good slump resistance (no slipping of tiles)
- Improved workability

Emulsion fillers / joint filler compounds

0.5 - 0.8 % ARBOCEL B 600 or
ARBOCEL B 00 by weight

Advantages with ARBOCEL:
- Inhibits cracking and shrinking
- Improves workability
- Improves sandability

 

Emulsion paints (semi gloss and flat)
a) paints for airless spray application

1.0 - 5.0 % ARBOCEL BE 600/30 PU by weight

Advantages with ARBOCEL:
- Suppresses sheen
- Improves rheological properties
- Reduces density
- Inhibits cracking

سیستم های اتصال امولسیونی / سیستم های چسب
رنگ های امولسیونی (نیمه شفاف و صاف)   

a - رنگ های مربوط به کاربرد اسپری بدون هوا

1 -  5 % ARBOCEL BE 600/30 PU درصد وزنی

مزیت های ARBOCEL :
- کاهش دادن درخشندگی
- بهبود ویژگی های رئولوژیک
- کاهش تراکم
- ممانعت از ترک خوردگی

 

 

b) Facade paints applied by roller or brush

0.5 - 3.0 % ARBOCEL B 00 or
ARBOCEL BWW 40 by weight.

Advantages with ARBOCEL:
- Improves rheological properties
- Suppresses cracking and shrinking
- thicker applied coats

b - رنگ های نمای به کار رفته توسط رولر یا برس

0.5 تا 3 % ARBOCEL B 00 یا ARBOCEL BWW 40 درصد وزنی

مزیت های ARBOCEL :
- بهبود ویژگی رئولوژیک
- از بین رفتن ترک خوردگی و جمع شدگی یا شیرینکیج
- ایجاد پوشش های ضخیم تر

 

 

c) crack-bridging reinforcing paints

0.4 - 0.8 % ARBOCEL BC 200 or
ARBOCEL BC 1000 by weight

Advantages with ARBOCEL:
- crack suppression
- improves rheological properties

c - رنگ های تقویت کننده پر کردن ترک

0.4 تا 0.8 % ARBOCEL BC 200 یا ARBOCEL BC 1000 درصد وزنی

مزیت های ARBOCEL :
- جلوگیری از ترک
- بهبود ویژگی های رئولوژیک

 

 

E. Bituminous Systems

ARBOCEL Grades Used:

The grades most commonly used in the bitumen sector are ARBOCEL ZZ 8/1 G and ARBOCEL ZZC 500. when used as an asbestos replacement, 30 % to maximum 50 % by weight of the asbestos quantity previously used is usually sufficient.
The resulting deficiency of volume should be compensated for by the addition of a suitable filler.

ARBOCEL cellulose fiber result in:
- Greater thickening
- Extremely good slump resistance even in hot environments (over 90 C)
- Good workability

In comparison to group 7 asbestos, ARBOCEL ZZ 8/1 G gives a rougher and less glossy surface. If a smoother surface is required, it is recommended that ARBOCEL ZZC 500 be used. since this product is a shorter fiber, 20 - 40 % more ARBOCEL by weight must be added in comparison to ARBOCEL ZZ 8/1 G.

 

سیستم های قیری

کیفیت به کار رفته:

رایج ترین مواد کیفی به کار رفته برای سکتور قیر عبارتند از: آربوسل ZZ 8/1 G و آربوسل ZZC 500
به هنگام استفاده از این ماده به عنوان جایگزین آزبست غالباً 30 تا حداکثر 50 درصد وزن آزبست تاکنون مورد استفاده کفایت می کند.
نقصان به وجود آمده از این طریق در زمینه ماده جامد را بایستی با افزودن میزان مناسبی از ماده پرکننده جبران کرد.

الیاف سلولزی آربوسل باعث:
ضخامت با ثبات تر
مقاومت بسیار بالا حتی در دمای بیش از 90 درجه سانتی گراد
و ساخت و پرداخت خوب می شوند

در مقایسه با آزبست گروه 7، با استفاده از آربوسل ZZ 8/1 G سطح زیرتر و نه چندان براقی به دست می آید. در صورتیکه مایل به داشتن سطحی صافتر هستید، توصیه می شود با آربوسل ZZC 500 کار کنید. از آنجایی که در آربوسل ZZC 500 الیاف کوتاهتری به کار رفته، بنابراین در مقایسه یا آربوسل ZZ 8/1 G باید به میزان 20 تا 40 درصد وزن بیشتر مورد استفاده قرار گیرد.

 

Guidance Notes:

- The longer the average fiber length of the ARBOCEL grade, the greater is its yield and the more the viscosity is increased.
- The larger the amount of ARBOCEL used, the greater the cross-linking effect of the fiber structure formed. The fiber structure enhances the thermal resistance of the formulation.
- The fiber structure results in bitumen being deposited on the fiber.
- The shorter the average fiber length of the ARBOCEL grade, the smoother the surface of the finished product.
- If dissolvers are used, we recommend that the fibers be added at the end of the blending process.
- With moderate to low-viscosity cold bitumen compounds, sedimentation may occur. this can be inhibited by stabilizers such as magnesium coated silicates or pyrogenic silicic acids.
-In the case of bitumen systems that are applied by airless spray, the correct ARBOCEL grade for the nozzle size must be used to prevent clogging.
- The use of ARBOCEL fibers can result in a subsequent thickening effect, thus raising the viscosity. This effect also occurs in bitumen products containing solvents (sol-gel changes), especially in cold bitumen with a petroleum spirit base. Normally this effect runs its course in a matter of a few days.
-It is also interesting to note that the softening point is higher when the same amount is added in comparison to asbestos 7 M and that it also increases more steeply.

 

راهنمایی ساخت و پرداخت / نحوه تاثیر

- هرچه طول میانگین الیاف مواد کیفی آربوسل بیشتر باشد، نتیجه بهتری حاصل شده و ویسکوزیته به همان نسبت افزایش می یابد.
- هرچه طول میانگین الیاف آربوسل کوتاهتر باشد، سطح محصول نهایی صافتر خواهد بود.
-  در صورت ذوب شدن توصیه می کنیم تا الیاف را در انتها به مخلوط موجود اضافه کنید.
- در مورد توده های قیر سرد دارای ویسکوزیته پایین یا متوسط احتمال بروز ته نشست (رسوب) وجود دارد که می توان از طریق مواد ثبات بخشی همچون سیلیکات منیزیم با اسید سیلیس دار ذوبی مانع آن شد.

-در سیستم های بدون هوای قابل تزریق بایستی متناسب با بزرگی افشانه (زنبورک) میزان مناسب از آربوسل را به کار برد، در غیر این صورت خطر گرفتگی وجود دارد.
- بایستی توجه داشت که الیاف آربوسل به طور مثال در توده های بطونه قیری می توانند منجر به اثر پس ضخامت (ضخیم شدن لایه پس از عملیات) شوند، که خود باعث افزایش ویسکوزسته می گردد.
- این اثر در قیر حاوی ماده محلول نیز بروز می کند، بویژه در مورد قیر سرد بر پایه ماده محلول بنزین تست، در موارد معمولی این پس ضخامت پس از گذشت چند روز غالباً برطرف می شود.
- این موضوع  نیز مطمئناً جالب است، که نقطه نرم شدن به همان میزان مساوی ماده افزودنی در مقایسه به آزبست 7 بیشتر است و در یک پیچ تندتر به شکل قابل توجهی افزایش می یابد.

 

 

Applications / Quantities

Vibration dampening pads

These are 2 mm embossed sheets which are usually applied directly to car panels to suppress noise.

Amount used:
0.8 - 3.0 % ARBOCEL ZZ 8/1 G by weight

Advantages with ARBOCEL:
- Increases heat resistance
- replaces asbestos
- improves working properties

 

سیستم های قیر اندود حوزه مصرف / میزان مصرف

سطوح آگوستیک

آنچه در این بخش معرفی می شود، سطح نورد شده یا ضخامت 2 میلی متر هستند، که اساساً به منظور گرفتن صدا مستقیماً روی ورقه بدنه اتومبیل چسبانده می شوند.

میزان مصرف: 3 - 0.8 درصد وزن آربوسل ZZ 8/1 G

مزایای استفاده از آربوسل:
- افزایش مقاومت و ثیات در برابر گرما
- جایگزینی برای آزبست
- ویژگی های پرداخت بهتر

 

 

Expansion Bands

These are used as a joint material, e.g. in highway construction in the joint between consolidation strips (concrete to asphalt or concrete to concrete). The taps is activated by heating.

Quantity used:
approx. 5.0 - 8.0 % ARBOCEL ZZ 8/1 G by weight

Advantage with ARBOCEL:
- Greatly increases heat resistance
- Replaces asbestos
- Improves working properties

 
 

نوارهای انبساطی (کششی)

 از این نوارها به عنوان ماده درزگیرر استفاده می شود، به طور مثال در اتوبان ها به عنوان درزگیر به هنگام تغییر نوارهای تثبیت کننده (ضخامت بتون به آسفالت یا صفحه بتون به صفحه بتون). جهت پردازش و کار بایستی نوار عایق حرارت داده شود.

میزان مصرف: حدود 8 - 5 درصد وزن ZZ 8/1 G

مزایای استفاده از آربوسل:
- افزایش مقاومت و ثیات در برابر گرما
- جایگزینی برای آزبست
- ویژگی های پرداخت بهتر

 

 

Filler compounds / putty

3.0 - 6.0 % ARBOCEL ZZ 8/1 G by weight
4.0 - 7.0 % ARBOCEL ZZC 500 by weight for smoother surfaces

Advantages with ARBOCEL:
- Replaces asbestos
- Greatly increases heat resistance
- Inhibits cracking

Note:
ARBOCEL is usually used only in medium and high-viscosity systems.

سیستم های قیراندود (سیستمهای حاوی ماده حلال و آب)
توده های ماله ای / بتونه ای

میزان مصرف:
3 - 6 درصد وزن آربوسل ZZ 8/1 G
7 - 4 درصد وزن آربوسل ZZC 500 برای سطوح صاف تر

مزایای استفاده از آربوسل:
- جایگزینی برای آزبست
- افزایش شدید ثبات و مقاومت حرارتی
- پوشاندن ترک ها

توضیح:
از آربوسل به طور معمول برای سیستم های دارای ویسکوزیته متوسط بالا استفاده می شود.

 

 

Medium and high-viscosity spray and brush-applied compounds

2 - 4 % ARBOCEL ZZ 8/1 G by weight (brush-applied use)
3 - 5 % ARBOCEL ZZC 500 by weight (spray-applied use)

Advantage with ARBOCEL:
- Replaces asbestos
- Inhibits cracking
- Permits thicker coats to be applied in one process
- Greatly increases heat resistance of coats, i.e. no running down vertical walls

مواد پاششی و مالشی دارای ویسکوزیته متوسط و بالا

4 - 2 درصد وزن آربوسل ZZ 8/1 G (قابل استفاده با فرچه)
5 - 3 درصد آربوسل ZZC 500 (قابل استفاده بصورت پاششی)

مزایای استفاده از آربوسل:
- جایگزینی برای آزبست
- پوشاندن ترک ها
- امکان پوشاندن سطوح دارای لایه ضخیم در یک مرحله کاری
- مقاومت و ثبات حرارتی بالای لایه به این معنا که در دیوارهای عمودی شره نمی کند.

 

Roof coatings (with or without aluminum)

2.0 - 6.0 % ARBOCEL ZZC 500 or ARBOCEL ZZ 8/1 G by weight

Advantages with ARBOCEL:
- Replaces asbestos
- Greatly increase heat resistance
- Reduces tendency of aluminum particles (in product) to settle out
- In bitumen foils partial replacement of SBS possible

Note:
In general when ARBOCEL is used in bitumen emulsions it must be ensured that the ARBOCEL is added in small portions to the bitumen emulsion while stirring. (If too much ARBOCEL is added, the bitumen emulsion can separate and form clumps). The rest of the materials can then be added and blended.
ARBOCEL is usually used in anionic bitumen emulsions.

سیستم های قیراندود (سیستمهای حاوی ماده حلال و آب)
روکش پشت بام (با و بدون آلومینیوم)

4 - 2 درصد وزن آربوسل ZZ 8/1 G (قابل استفاده با فرچه)
5 - 3 درصد آربوسل ZZC 500 (قابل استفاده بصورت پاششی)

مزایای استفاده از آربوسل:
- جایگزینی برای آزبست
- مقاومت و ثبات حرارتی
- از رسوب احتمالی اجزاء آلومینیوم جلوگیری می کند.

توضیح:
به صور کلی در امولسیون قیری با آربوسل بایستی حتماً به این نکته توجه شود که آربوسل بایستی به تدریج و به میزان کم  و در حالت هم زدن به امولسیون قیری اضافه شود (در صورتیکه آربوسل را به مقادیر زیاد اضافه کنیم، امولسیون قیری شکسته و کلوخه تشکیل می شود). پس از آن بایستی بقیه ماده را اضافه و هموژنیزه کرد.
در امولسیون قیری دارای بار مثبت نمی توان از آربوسل استفاده کرد.

 

 

F. LIGNOCEL

Application

LIGNOCEL wood fiber materials are used in construction chemical products only if the wood constituents (lignin, resin and hemicellulose) will not adversely affect the finished product (wood constituents can result in yellowing, bleaching or discoloration).

Smoothing compounds
Approx. 30 - 40 % LIGNOCEL C 120 by weight

Advantages with LIGNOCEL:
- Improves working properties
- Makes for amore cost-effective filler

 

 

Magnesite-bound Flooring Compounds

Approx. 30 - 40 % LIGNOCEL 9 by weight

Advantages with LIGNOCEL:
- Stabilizes the mixture
- Reduces cracking during setting
- Promotes slow, uniform setting